rrTV-PHOTO   New HD TV
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 724 ONLINE 28 EVENTS SEARCH REGISTER  START HERE
 
1 page906 viewsPOST REPLY
MTA Hobbies . Model Rectifier Corp . 3D Heli Depot

.
.
Got Jet Fuel? Turbine Helicopters > Jetcopter and JR 10x
 
 
midwestpilot
Elite Veteran
Location: Crystal Lake, IL

I have an 8103....but I would love to get it on the 10x instead...anyone done this with the 4 servo ccpm...I know i need to use mixes...If you have JR's Data safe...I would be even happier with the file via email.

I have searched RR and I came up with these mixes..but with such a $$$ birdy...I thought I would ask you guys for some help.

Mix 51 Elev(M) - Aux2(S) Offset (-100), Zero (-100), Trim On
Mix 52 Aile (M) - Pit (S) Offset (-100), Zero (-100), Trim On
Mix 55 Pit (M) - Elev (S) Zero In =100 Out, 100 In = (-100) Out, Linear
Mix 56 Pit (M) - Aux2(S) Zero In =100 Out, 100 In = (-100) Out, Linear
Mix 57 Pit (M) - Aile (S) Zero In =100 Out, 100 In = (-100) Out, Linear

Anyone?

In life there is no spacebar!

Rich Erikson AMA 6175
05-22-2003 Over year old.
HOMEPAGE  
 
 
Bill Ludwig
Veteran
Location: Tucson, AZ

Just do a search here on RunRyder, Rich - there's tons of info on using the 10x with CCPM.

- Bill
05-23-2003 Over year old.
 
 
midwestpilot
Elite Veteran
Location: Crystal Lake, IL

got the answer

Here is what I have found out.
4 Servo CCPM 10X programming steps
Step #1. In code 65 select the 1 servo swash plate mix.

Note: Steps 2 thru 4 are needed to synchronize the servo throw and to prevent over travel. Initial setup values are given below. During final setup and adjustments the pitch curves (code 68) and dual rates (code 13) will be used to achieve the desired pitch, aileron and elevator travel (do not use travel adjust).

Step #2. Code 12 travel adjust- Increase the aileron, elevator and pitch travel adjustments to 150% in each direction.

Step #3. Code 13 dual rate- adjust the dual rate values for aileron and elevator to 50% in all dual rate positions (0, 1,2).

Step #4. Code 68 pitch curve- Reduce the high pitch setting to 75% and the low pitch setting to 25% in all flight modes (0, 1,2, H).

Step #5. Code 51 mix 1- Mix pitch to aileron at 100% in each direction

Step #6. Code 52 mix 2- Mix aileron to pitch at 100% in each direction an turn on the trim.

Step #7. Code 53 mix 3- Mix pitch to elevator at 100% in each direction.

Step #8. Code 54 mix 4- Mix elevator to aux 2 at 100% in each direction and turn on the trim.

Step #9. Code 55 mix 5- Mix Pitch to Aux 2 at 100% in each direction.

Servo assignment
Forward servo- elevator
Rearward servo- Aux. 2
Right servo - Aileron
Left aileron- Aux. 1

Enjoy

In life there is no spacebar!

Rich Erikson AMA 6175
06-10-2003 Over year old.
HOMEPAGE  
 
 
zzmotorzz
Heliman
Location: atlanta ga.

admendum for JR 10X set up for Graupner NH-90 Jet

ADMENDUM!!! FOR NH-90 JET
By: Zach de la Torre
4 Servo CCPM 10X programming steps

Step #1. In code 65 select the 1 servo swash plate mix.

Note: Steps 2 thru 4 are needed to synchronize the servo throw and to prevent over travel. Initial setup values are given below. During final setup and adjustments the pitch curves (code 68) and dual rates (code 13) will be used to achieve the desired pitch, aileron and elevator travel (do not use travel adjust).

Step #2. Code 12 travel adjust- Increase the aileron, elevator and pitch travel adjustments to 150% in each direction.
(YOU MUST ALSO INCRESE AUX.2 TO 150% IN EACH DIRECTION TO OBTAIN LINEAR SERVO TRAVEL FOR ALL 4 SERVO’S)

Step #3. Code 13 dual rate- adjust the dual rate values for aileron and elevator to 50% in all dual rate positions (0, 1,2).

Step #4. Code 68 pitch curve- Reduce the high pitch setting to 75% and the low pitch setting to 25% in all flight modes (0, 1,2, H).

Step #5. Code 51 mix 1- Mix pitch to aileron at 100% in each direction

Step #6. Code 52 mix 2- Mix aileron to pitch at 100% in each direction an turn on the trim.

Step #7. Code 53 mix 3- Mix pitch to elevator at 100% in each direction.
ONCE YOU HAVE SET THE VALUES TO +100% IN THIS STEP, YOU WILL NEED TO PRESS THE TURN BUTTON ON THE SCREEN TO GET –100% IN ORDER FOR THE PITCH TO TRAVEL CORRECTLY

Step #8. Code 54 mix 4- Mix elevator to aux 2 at 100% in each direction and turn on the trim.

Step #9. Code 55 mix 5- Mix Pitch to Aux 2 at 100% in each direction.

NOTE: YOU WILL HAVE REVERSE CHANNEL 3 (ELEVATOR) IN ORDER TO GET THE ELEVATOR SERVO’S TO MOVE IN OPPOSITE DIRECTIONS.

Servo assignment

Forward servo- elevator
Rearward servo- Aux. 2
Right servo – Aileron
Left aileron- Aux. 1
07-30-2003 Over year old.
HOMEPAGE  
 
 
1 page906 viewsPOST REPLY
JR-Spektrum . Gyro Hobbies . E-flite

.
.
Got Jet Fuel? Turbine Helicopters > Jetcopter and JR 10x
  UPDATE SCREEN   PRINT TOPIC Advertisers 

Subscribe to This Topic

Wednesday, October 8 - 2:40 am - Copyright © 2000 - 2008 runryder.com | email | link to rr | runryder needs cookie