RunRyder - screw stripped

rrTV-PHOTO

New HD TV

HOME rrTV-PHOTO GALLERIES MY GALLERY HELP-FAQ

myHOME PM pmRR MEMBERS 554 ONLINE 43 EVENTS SEARCH REGISTER START HERE

1 page

322 views

POST REPLY

Autography FlightPower	.	Advantage Hobby	.	Revolution Models
	.		.

Off Topics > screw stripped

michael88997
Veteran
Location: northern texas, us

ok i was taking the set screw that holds the tail on the shaft and it stripped out... can i use this to get it out?

http://www.sears.com/shc/s/p_10153_...C+Taps+%26+Dies

---------------------------------
hurricane 550

05-09-2008 09:31 PM

RobRoy
Key Veteran
Location: Huntsville, Alabama

I don't think even the smallest one in that kit will fit the grub screw in your tail. If you can, try cutting a small straight slot in the screw with a dremel cut off wheel. Good luck.

Ignorance is curable, stupidity is for life.

05-09-2008 09:35 PM

rcfreak7
Senior Heliman
Location: southern california

or epoxy an alen wrench in the stripped screw

squish the bread to save the berries

05-09-2008 10:16 PM

TRACERBOB
Senior Heliman
Location: Panama City, FL USA

If its all metal parts, try heating the set screw with the small tip of a soldering iron to get the locktite to soften up. It should work.

05-09-2008 10:25 PM

legoman67
Elite Veteran
Location: Nanoose Bay B.C, Canada

Quote
If its all metal parts, try heating the set screw with the small tip of a soldering iron to get the locktite to soften up. It should work.

that works, if the screw isnt already to far gone, and also be very carefull to not melt the plastic.

Matt M.
http://www.filepile.ca

05-10-2008 12:18 AM

HOMEPAGE

himaxkeith
Senior Heliman
Location: eht nj usa

If its an allen screw that is damaged try to start with your allen driver grind down a 1/8 or 1/16 of an inch off your allen driver so to so the end is nice and fresh or square then heat it till its cherry red stick it in the screw so it heats the the screw up for about thirty seconds then try to back it out

05-10-2008 01:53 AM

Ralphw
Key Veteran
Location: Spring, TX

Here is the set you want...Craftman Drill Out.

I bought this set a couple of weeks ago to remove a stripped set screw on my start shaft adapter and worked exceptionally well. The smallest (3mm) is so small it was too small for the set screw and I had to use the 4 mm size. Not a cheap set, but one I'm really happy to have in my bag of goodies.

Ralph W.
"Life's Short, Fly Fast"

05-10-2008 03:38 AM

HOMEPAGE

maxpower097
Senior Heliman
Location: none

Theres always the "As seen on TV" Grab-It screw and bolt remover....

05-10-2008 06:57 PM

michael88997
Veteran
Location: northern texas, us

ok nothing worked so i just bought a new tail drive shaft... now my problem is the pin that holds the tail pully gear on isn't budging... does anybody have any tips to get this pin out, ive been using a 1.5mm driver to push on it but its not working... btw this is on a gaui 550

---------------------------------
hurricane 550

05-16-2008 10:06 PM

cfranks
Veteran
Location: Adelaide South Australia

Have a look for a grub screw hole in the end of the shaft. Some manufacturers use a grub screw in the shaft to hold the pin in the gear/shaft.

05-17-2008 12:17 AM

1 page

322 views

POST REPLY

CarbonXtreme	.	Midland Helicopters	.	HeliProz
	.		.

Off Topics > screw stripped

UPDATE SCREEN PRINT TOPIC

Advertisers

Subscribe to This Topic