RunRyder - Crashed the K3d today.....

rrTV-PHOTO

New HD TV

HOME rrTV-PHOTO GALLERIES MY GALLERY HELP-FAQ

myHOME PM pmRR MEMBERS 622 ONLINE 44 EVENTS SEARCH REGISTER START HERE

1 page

447 views

POST REPLY

Century Helicopter	.	MTA Hobbies	.	MRC/Altech Marketing USA
	.		.

Compass Knight 50 > Crashed the K3d today.....

Tradhunt
Senior Heliman
Location: American Canyon, Ca. USA

Well I was out flying a bit today everything going great. Doing some loop's,roll's,etc. Then all of a sudden my tail started twitching to the right I tried to correct it but nothing. I was lucky able to land it somewhat safely being it was coming down sideway's got it corrected and lucally I was able to land it upright somehow behind a little hump in the ground. Damage dosent look to bad... Blade's, flybar, mainshaft, landing gear mount's, look's like all I see so far...

04-28-2008 12:42 AM

eyeflyhelis
Elite Veteran
Location: charlotte nc

thats not to bad looking.

only you have the power to make no difference!
**Modefo's Heli's**
K3D!!

04-28-2008 04:10 AM

HOMEPAGE

Tradhunt
Senior Heliman
Location: American Canyon, Ca. USA

No it's really not. I was surprised I thought for sure I'd walk over to a mangled mess...

04-28-2008 04:22 AM

eyeflyhelis
Elite Veteran
Location: charlotte nc

g-10 is some strong stuff! these helis hold up to my crash standards as well as EFS!!

only you have the power to make no difference!
**Modefo's Heli's**
K3D!!

04-28-2008 02:07 PM

HOMEPAGE

helimatt
Key Veteran
Location: Lafayette, IN

so, what happened to cause loss of tail control? Sounds like what happened when my tail servo burned out (running on too-high voltage)...

Never, ever, ever, ever give up.

04-28-2008 05:45 PM

Tradhunt
Senior Heliman
Location: American Canyon, Ca. USA

Total damaged part's... Landing gear mount's, Flybar, Replaced the main shaft..I't looked ok but might of been a little bent so I went on the safe side and replaced it, Landig gear broke ( no biggie they were just Align) and boom support's ..again only align's so no biggie...

As for the tail I'm not sure what went wrong. It's a 770/8900g volt's are fine checked it... I think it was in my programming I had a very small tail wag but it went away. I think I'm gonna go back and put my 6100T back on the heli.

04-29-2008 12:41 AM

SteveH
rrProfessor
Location: Texas

Did you check the spindle? If you have the 6mm spindle, it's hard to believe it didn't bend.

SteveH
Magnum Fuel
AMA76186

04-29-2008 01:06 AM

Tradhunt
Senior Heliman
Location: American Canyon, Ca. USA

No it's the 8mm spindle.. Glad it didn't I don't have any and the place I ordered some from were on backorder.. I'll have to get some more comming from somewhere else also..

04-29-2008 01:29 AM

eyeflyhelis
Elite Veteran
Location: charlotte nc

im pretty sure modefos.com has them in stock.

only you have the power to make no difference!
**Modefo's Heli's**
K3D!!

04-29-2008 03:27 AM

HOMEPAGE

Tradhunt
Senior Heliman
Location: American Canyon, Ca. USA

Not yet from what I know.. I talked to Wes a couple week's ago on when he was expecting somemore 600E Knight and if he had some spindle's and such but he didn't have any and said he would get some on order.. Do you know the part # for the 8mm spindle..

04-29-2008 03:35 AM

erl919
Heliman
Location: Philippines

02-0113 8mm spindle 2pcs/bag

04-29-2008 03:45 AM

eyeflyhelis
Elite Veteran
Location: charlotte nc

02-0113 Spindle if im not mistaken
and the 0112 is the 6mm

only you have the power to make no difference!
**Modefo's Heli's**
K3D!!

04-29-2008 03:46 AM

HOMEPAGE

Tradhunt
Senior Heliman
Location: American Canyon, Ca. USA

Got it thanks for the help... I just needed to stop being lazy and look it up. Thanks again..

04-29-2008 03:51 AM

1 page