rrTV-PHOTO   New HD TV
HOME   rrTV-PHOTO   GALLERIES   MY GALLERY   HELP-FAQ
myHOME PM pmRR MEMBERS 486 ONLINE 72 EVENTS SEARCH REGISTER  START HERE
 
5 pages [ <<    <     1     ( 2 )     3      4     NEXT    >> ]3659 viewsPOST REPLY
Esprit Model . Thunder Power RC . Real Raptors

.
.
Audacity Models Pantera 50 - Tiger 50 > BBC update
 
 
rsalazar
Key Veteran
Location: Florida, USA

I hope John does not take too long on finishing the parts
02-10-2008 03:13 AM
 
 
MartyH
Veteran
Location: Lawrenceburg, Indiana

Oh Man! I hand ground a nut using the drill press to spin it and a file setup in a vice clamped to the drillpress table to cut the taper. The runout was terrible on the OS engines I have, I could never get below .007 on either engine but on the Webra .61 P5 AAR I happen to have, the thing centers itself within .001 with little effort! Now, if I could only come up with the carb drawbar, I'd be willing to spend the time to make a little tool to finish tightening the clutch hub nut I made and be on my way to my first Pantera Big Block. Anyone know where I can get the Webra part 1056-16O? This is the carb drawbar for the Webra .61, 75 and .91s. Horizon and SouthEast don't have it.

Marty,
6 Raptors, Hawk Pro
EVO 50, Knight 3D
2 Audacity Panteras & Tiger 50
02-11-2008 12:33 PM
HOMEPAGE  
 
 
billm
Key Veteran
Location: Liberty Lake, WA

Any ideas on where I can find a tuned pipe for my O/S 61?

My name is Billm. Cough, and I'm a Heli Holic
02-12-2008 03:34 AM
 
 
rsalazar
Key Veteran
Location: Florida, USA

Try this one

HATMSB16FH - HATORI SB16FH MUFFLER WITH FLANGE MOUNT OS/YS

http://www.ronlund.com/Merchant2/me...Code=HATMSB16FH
02-12-2008 04:18 AM
 
 
rsalazar
Key Veteran
Location: Florida, USA

MartyH

Check the US reseller for Webra. But, the one I know that has the part is:

http://www.rcmarket.org/1056-16O-Ca...lt-p-15347.html
02-12-2008 04:35 AM
 
 
billm
Key Veteran
Location: Liberty Lake, WA

rsalazar
Ouch, That pipe is almost the cost of my my motor.
I am thinking of returning the .61 and looking for another BBC motor.

My name is Billm. Cough, and I'm a Heli Holic
02-13-2008 02:50 AM
 
 
Mr.HillBilly
Senior Heliman
Location: Salesville, OH - USA

Hey Blim take a look at this http://cgi.ebay.com/ws/eBayISAPI.dl...em=320213628480

I was thinking about getting it and I changed my mind. It ended a few days ago but he may still have it.
02-13-2008 03:02 AM
 
 
billm
Key Veteran
Location: Liberty Lake, WA

Sold, Oh well.
Thanks for the link.

My name is Billm. Cough, and I'm a Heli Holic
02-13-2008 03:07 AM
 
 
Mr.HillBilly
Senior Heliman
Location: Salesville, OH - USA

OK try this one http://cgi.ebay.com/60-size-Heli-Tu...emZ220200408941
02-13-2008 03:14 AM
 
 
billm
Key Veteran
Location: Liberty Lake, WA

WOW, what a busy pipe. kinda like my old Ninja pro pipe from back in the day. Looking for a MPII clone type pipe. I have the LHS working the cundrudrum.

My name is Billm. Cough, and I'm a Heli Holic
02-13-2008 03:20 AM
 
 
jbeech
rrAdvertiser
Location: Sanford, FL (Orlando area)

That's a tuned pipe and I'd recommend you leave well enough alone and look for a muffler. century sells one pretty cheaply, which works OK if you don't find something used.


John Beech - GM (and janitor)
Audacity Models
02-13-2008 12:43 PM
 
 
billm
Key Veteran
Location: Liberty Lake, WA

Mr.HillBilly
I just put a "bid" on the link you posted. I figure I can install the beast and make the pantera look real bad. If it does not fit. I can sell the package. What the heck. It's only Money. Besides I want a tuned pipe!

My name is Billm. Cough, and I'm a Heli Holic
02-14-2008 03:12 AM
 
 
Australia 50
Heliman
Location: wollongong nsw Australia

when you get the big block conversion do you need to do any thin else apart from swap the engine mount and pu the 61 in

pantera 50
02-14-2008 05:30 AM
 
 
rsalazar
Key Veteran
Location: Florida, USA

You should also have clutch hub, and engine nut
02-14-2008 02:17 PM
 
 
Australia 50
Heliman
Location: wollongong nsw Australia

is the os 50 and 60 engine nuts the same and do i need to get another clutch hub then the one ive got

pantera 50
02-15-2008 05:05 AM
 
 
jbeech
rrAdvertiser
Location: Sanford, FL (Orlando area)

This has been explained before. Rather than go into it again, just search on BBC here in the Audacity Forum and you'll find plenty of information.


John Beech - GM (and janitor)
Audacity Models
02-15-2008 10:38 AM
 
 
MartyH
Veteran
Location: Lawrenceburg, Indiana

No, the nuts are not the same. The hubs are not the same though you could drill one out and if you had a thin enough nut that you can get a turned down socket in there, you could use a 50 hub drilled out.. The 50 size engines are 1/4" studs, the 60 and 70 engines are 5/16-24. The engine mount is also going to be different. You could use some 5/16" stock and drill your own rails for now. 5/16" X 3/8" X 2" X 2 pieces will get you what you need.

Marty,
6 Raptors, Hawk Pro
EVO 50, Knight 3D
2 Audacity Panteras & Tiger 50
02-15-2008 12:57 PM
HOMEPAGE  
 
 
Mr.HillBilly
Senior Heliman
Location: Salesville, OH - USA

Hey Blim I thought it would look good also. I was going to bid if no one else did myself, but I do not need it so I will hold off since you are in on it. Post a pic for me.
02-15-2008 01:43 PM
 
 
billm
Key Veteran
Location: Liberty Lake, WA

If you want to bid on it go ahead. I have another muffler coming in as well. Thanks my friend. Go for it.
billm

My name is Billm. Cough, and I'm a Heli Holic
02-15-2008 09:31 PM
 
 
billm
Key Veteran
Location: Liberty Lake, WA

Pnatera #5 on order for the BBC

I guess the tuned pipe is mine. Oh well. Thats life in the E-Bay world. Anybody need a tuned pipe? I have a another pipe on the way to fit my 61.
I just pulled the trigger on yet another Pantera. This would make number 5. I killed two panteras so this one will be the third in the race ready fleet. I figure the new one will be for the BBC.
I hate pulling apart a good chopper to do mods. Just get a new one to play with.
This is going to be a great summer.
EVO 90 with all the bling that god could muster.
2 Panteras (soon to be 3)
1 Tiger Night ship
1 Scale Augusta 109
1 Blade 400 3D (stick time at lunch)
1 Cat that likes to push parts around on the bench!

My name is Billm. Cough, and I'm a Heli Holic
02-20-2008 01:54 AM
 
 
5 pages [ <<    <     1     ( 2 )     3      4     NEXT    >> ]3659 viewsPOST REPLY
Mikado Modellhubschrauber . GrandRC . CanoMod

.
.
Audacity Models Pantera 50 - Tiger 50 > BBC update
  UPDATE SCREEN   PRINT TOPIC Advertisers 

Subscribe to This Topic

Saturday, May 17 - 1:41 pm - Copyright © 2000 - 2008 runryder.com | email | link to rr | runryder needs cookie