RunRyder - To shim or not to shim

rrTV-PHOTO

New HD TV

HOME rrTV-PHOTO GALLERIES MY GALLERY HELP-FAQ

myHOME PM pmRR MEMBERS 524 ONLINE 45 EVENTS SEARCH REGISTER START HERE

1 page

632 views

POST REPLY

Mikado Modellhubschrauber	.	GrandRC	.	CanoMod
	.		.

Synergy R/C Synergy N9 > To shim or not to shim

harveyhugo
Senior Heliman
Location: Cheshire, UK

Putting my Synergy together and wondering whether in most kits the additional shim above the bottom main shaft bearing block is required.

I haven't added it as the manual states if required and I'm now wondering whether I should of added it. Thoughts please

So far my build is going well, although still have yet to get the hang of those pesky circlips!!!

Has anyone received decals with their kit as there were none in my box?

2 x Trex 600N, 2 x Synergy N9

07-28-2006 Over year old.

HOMEPAGE

Will B
Veteran
Location: Bicester, Near Oxford, UK.

no decals in my kit and no boom either. Bob if yer reading this I need a boom please!!!

Cheers, Will.

07-28-2006 Over year old.

sestcourt
Senior Heliman
Location: Bracknell, Berkshire, UK

Nope, no decals in my kit either....

However the rest of the heli is going together fairly well. Off to the 3D Masters in the morning, so hoping to have her finished and flight worthy for Monday night with a bit of luck....

07-28-2006 Over year old.

HOMEPAGE

raptorheli2
Elite Veteran
Location: rip off britain and no changing it

no decals in my kit either, i guess the 1st batch isn't going to come with them then.

cheers

www.waterfoothelis.com

07-29-2006 Over year old.

HOMEPAGE

RockDoc
Senior Heliman
Location: Middlesbrough, England

No decals in my kit but never mind i've got a painting plan anyway.

Also only got three main blade grip bearing's and another odd one - very disappointing!

Luckily they are the same size as the Raptor 90 ones so I could swap one out.

Whilst building I snapped the head off one button head bolt when tightening and also snapped a ball in the blade grip arms. Luckily the spares bag contained another ball but it was a b** to get out. Must try not to be too heavy handed...

I did add the shim at the bottom main bearing block and it seems ok with it....

All built now and waiting to finish the canopy spraying today. Should be in the air tomorrow hopefully!

D.

Sponsored by Barclaycard!

www.clevelandheli.co.uk

08-01-2006 Over year old.

HOMEPAGE

hansking12
Senior Heliman
Location: irvine, ca

harvey

i found that i didn't need to use the shim. also, when you install the main shaft, press down on it while moving the set collar up against the upper bearing in its block.

try it without first and verify that the mesh is correct before adding it.

regards,

hans

08-01-2006 Over year old.

DrScoles
Veteran
Location: Redmond WA

No shim... built two of them, tail mesh was perfect without the shim..

Mike

08-03-2006 Over year old.

harveyhugo
Senior Heliman
Location: Cheshire, UK

Perfect without shim in the end

2 x Trex 600N, 2 x Synergy N9

08-03-2006 Over year old.

HOMEPAGE

1 page

632 views

POST REPLY

Futaba-RC	.	A Main Hobbies	.	Boca Bearings
	.		.

Synergy R/C Synergy N9 > To shim or not to shim

UPDATE SCREEN PRINT TOPIC

Advertisers

Subscribe to This Topic